Skid mounted Cold 5.5 GPM 3500 PSI pressure washer 

Pressure Pro S/VB5535HGEA411

18” width x 32” long approximately

5.5 GPM 3500 PSI Honda GX630 General Pump HP5535 V-belt special powder coated steel frame, commercial lock up pressure trapped unloader, thermal relief valve, gun/wand assembly with brass quick connects, 50' high pressure hose with quick connects, 5 quick connect nozzles, 20% high draw chemical injector assembly with brass quick connects.

• Lifetime frame warranty
• Easy access single bolt interlocking belt cover
• Single bolt engine adjustable belt tension
• EZ-start
• Low oil shut-off
• Adjustable pressure unloader but is set at 3700 psi and meant to be left alone and never adjusted
• Engine and pump oil drains offer easy maintenance
• Dual padded shock absorbing feet
• 3/4" cold-rolled steel threaded axle
• 3VX belt system offers balanced power transfer
• Commercial/industrial grade engines
• Low speed pump and thermo-sensor (Prevents overheating in bypass mode)
• Remote six gallon poly fuel tank-non-carb evaporative compliant-not for sale to California
• All units feature electric start and include marine battery box
• Must check belts after 30 days. No warranty on belts. Unloader settings, clogged nozzles and loose belts are some causes of belt failure.
• Can not be shipped inside the state of California

Note: All units are completely factory assembled, tested in the USA, and delivered ready to operate.

We highly recommend adding the best high pressure 3/8” ball valve (6292.SM) to this order to allow you to turn off the flow of water to switch from the gun to a Whisper Wash Classic surface cleaner).

The 19” Whisper Wash Classic is the perfect complement to this cold pressure washer. Keep in mind that the wider the surface cleaner, the slower you will move. 

This pressure washer will arrive with a Duraview inlet filter (Female garden hose inlet) installed into the left side of the manifold. A short length of 3/8” bypass hose connects the unloader to the Duraview filter. We strongly recommend that you remove the Duraview and replace with a HB1608B and a longer bypass hose to the tank using a 4468 bulkhead and 4796 brass barb. These items as well as everything needed for plumbing this unit to a tank are included in the PL-4TA for a horizontal leg or PCO tank or the PL-4TO for an IBC tote or caged tank.

You can order this pressure washer with a K7.2 flow actuated unloader. The flow actuated unloader will allow everything under pressure to last longer. You won't experience the strong kick-back when pulling a trigger, the hose will remain soft when releasing the trigger, quick connects last longer as well as the O-rings.

As with any pressure washer, do not adjust the unloader. The unloader is set at a spike pressure of 200 psi above the operating pressure of the pump and meant to be left alone. If you need less pressure, change out the nozzles to a larger orifice and never smaller than what is called for using factory specifications using GPM and pressure. Try a JROD with four nozzles chosen to apply soap up high and rinse down low for this unit, 6540-5.

Install a high temperature Hudson Float Valve (Hudson-HT) using everything you need to install it with our Hudson Assembly (Hudson-A or HB). The Hudson assembly installs into the very top of the tank using a bulkhead and garden hose connection to prevent the tank from over-flowing.

Inlet line size should be adequate to avoid starving the pump.

• Line size must be a minimum of one size larger than the pump inlet fitting. Avoid tees, 90-degree elbows or valves in the inlet line of the pump to reduce the risk of flow restriction and cavitation.
• The line must be a flexible hose, not a rigid pipe, and reinforced on suction systems to avoid collapsing.
• The simpler the inlet plumbing the less the potential for problems. Keep the length to a minimum, the number of elbows and joints to a minimum (ideally no elbows) and the inlet accessories to a minimum.
• Use pipe sealant to assure air-tight, positive sealing pipe joints.

SKU: PW.S/VB5535HGEA406